American Standard Outdoor Shower 2555050 User Manual

Installation  
Instructions  
TOWNSQUARE  
2555.050  
2555.091  
2555.051  
ACCESSORIES  
SOAP DISH  
TUMBLER WITH TOOTHBRUSH HOLDER  
LOTION/SOAP DISPENSER  
Thank you for selecting American-Standard...the benchmark of fine  
quality for over 100 years.  
To ensure that your installation proceeds smoothly--please read these  
instructions carefully before you begin.  
M968228C  
Recommended Tools  
CARE INSTRUCTIONS:  
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR  
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
Regular Screwdriver  
Phillips Screwdriver  
10'  
Drill  
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,  
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH  
WITH A COARSE SURFACE.  
Tape Measure  
SOAP DISH, LOTION/SOAP DISPENSER and TUMBLER WITH TOOTHBRUSH HOLDER  
MOUNTING & INSTALLATION  
1
2
The SOAP DISH (1), TUMBLER WITH TOOTHBRUSH HOLDER (2) and LOTION/SOAP DISPENSER (11) work best if secured to a wall stud  
or cross brace within the wall, using the SCREWS (4) supplied.  
If the SOAP DISH (1), TUMBLER WITH TOOTHBRUSH HOLDER (2) and LOTION/SOAP DISPENSER (11) are to be installed on a tile or plaster  
wall the DRYWALL ANCHORS (6) or TILE ANCHORS (8) and SCREWS (4) should be used.  
Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two  
spots for the mounting holes. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (4).  
For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (4) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips  
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with  
the wall. Place MOUNTING PLATE (5) over DRYWALL ANCHORS (6) and insert screws provided with #2 Phillips screwdriver. See  
illustration below. Secure MOUNTING PLATE (5) to wall with SCREWS (4).  
For installations on tiled walls, If TILE ANCHORS (8) and SCREWS (4) are use for securing MOUNTING PLATE (5), then  
drill two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (8) flush with face of the finished wall.  
Secure MOUNTING PLATE (5) to wall with SCREWS (4).  
INSTALL SOAP DISH, TUMBLER WITH TOOTHBRUSH HOLDER and LOTION/SOAP DISPENSER  
Place ESCUTCHEON (7) onto MOUNTING BRACKET (5), and secure with ATTACHMENT SCREW (3).  
Install the SOAP DISH (1), TUMBLER WITH TOOTHBRUSH HOLDER (2) or LOTION/SOAP DISPENSER (11) into the WALL ESCUTCHEON (7).  
Tighten SET SCREW (9) using 2-1/2mm HEX KEY (10) supplied to secure assembly to ESCUTCHEON (7).  
USE MOUNTING BRACKET (5)  
AS TEMPLATE  
1
FINISHED WALL  
2
5
8
6
5
7
4
3
9
4
8
10  
 

Acer Network Card 08P4100 User Manual
Acura Embedded Computer Hardware Small footprint rugged Pentium M User Manual
AEG Clothes Dryer T37800 User Manual
Agilent Technologies Ventilation Hood 6610XA User Manual
Aiphone Stereo System JK 1SD User Manual
Alesis Computer Monitor M1 Active Mk2 User Manual
Alpine GPS Receiver NVE M300 User Manual
Altec Lansing Speaker FX6021 User Manual
ATN Binoculars ATN NVG7 User Manual
Behringer Music Mixer PMP1680S User Manual