Audiovox Automobile Electronics 128 6927 User Manual

Rear Observation System Package  
Model RVMPKG3  
Installation Manual  
1
2
Features:  
·
·
·
·
Rearview Mirror with 4” LCD  
2 Built in Speakers  
Rearview Camera Input  
Auxiliary Video Input  
 
Cautions!  
The product is intended to assist in safe driving and to allow the driver to  
have a broader rearview while the vehicle is in reverse. You, as the driver,  
are solely responsible for the safe operation of your vehicle and the safety  
of your passengers according to the country and their local traffic  
regulations. Do not use any features of this system to the extent it distracts  
you from safe driving. Your first priority while driving should always be  
the safe operation of your vehicle. Audiovox Electronics Corporation  
cannot accept any responsibility whatsoever for accidents resulting from  
failure to observe these precautions or safety instructions.  
1.  
This product utilizes high voltage. Any unauthorized modifications  
or damage to the products may result in electrical shock. Handle  
all components with care. Inspect regularly for damage to  
components and cabling.  
2.  
You shall be responsible to ensure that the installation of this  
product does not void or affect the vehicle manufacturer’s  
warranty. Audiovox Electronics Corporation, or its branches are  
not liable in full or in part for improper installation resulting in  
loss or damage to your property, or for voiding all or part of the  
vehicle manufacturer’s warranty.  
3.  
4.  
Do not apply excessive force to any of the components contained  
within this kit. Excessive force used before, during or after  
installation that results in a damaged or non-functional part shall  
void all warranties.  
Please follow the procedure from this installation manual.  
Improper installation or modification of this product shall void all  
warranties.  
 
Preface  
There is a blind spot that exists at the back of a vehicle while the vehicle is  
in reverse. Equipped with a camera, this electronic rearview mirror  
ensures safety by providing the driver with a clear and wide image of the  
area behind the vehicle whenever SW1 is pressed.  
WARNING:  
Backing up vehicle  
Do not back up vehicle while watching the mirror/monitor screen. Always  
look in the direction of vehicle motion. Use the mirror/monitor as an aid  
in safety confirmation. The distance looks different in the monitor. The  
actual distance is shorter than it looks in the monitor. The range of image  
is limited. Beware of blind spots.  
Packing list  
The Rear Observation System Package Model consists of the following  
items:  
Item  
Description  
Rear View Mirror  
Power Cable  
Figure  
1
2
1
2
Red  
 
3
4
Adapter  
Fastening Belts  
5
6
Rearview Camera  
Camera Cable  
1. Installation Instructions  
(1) Mount the mirror/monitor onto the existing rearview mirror.  
a) Take the two belts and slide them into the slots on the top rear  
of the mirror with grooved side of the belt facing down..  
Figure 1  
b) Take the buckles and slide them into the lower slots on the rear of the  
mirror with the buckle facing down toward the strap.  
Figure 2  
NOTE: The large opened rectangle on the buckle will face away from the  
strap.  
c) Mount the new rearview mirror/monitor onto the existing one. Add  
 
the  
rearview mirror onto the existing mirror from one side with one fixed  
belt. Then fasten the other belt on the other side of the mirror. To  
prevent the mirror from falling off, tighten the belts until secure to the  
factory rearview mirror on both sides.  
Figure 3  
d) Cut off excess part of straps.  
(2) Wiring the System.  
1. RED FUSED WIRE: +12 VDC ACCESSORY SOURCE  
Connect this wire to a source that is 12 volts when the Ignition key switch  
is turned on, and 0 volts when the ignition key switch is turned off.  
2. BLACK WIRE: CHASSIC GROUND  
Connect this wire to a solid, metal part of the vehicle’s chassis.  
3. YELLOW WIRE: GROUND WHEN PARKING BRAKE IS  
APPLIED  
Connect this wire to the wire from the parking brake that turns on the  
parking brake light on the dash. This wire will have voltage on it while the  
Ignition key switch is turned on and 0 volts when the parking brake is  
pressed.  
(3) Connect the mirror cables adapter and power cable follows the fig.7  
illustration for connection.  
2. Signal Inputs  
The signal input connections for the system include:  
(1) Rear Camera: By connecting rear camera with 4 pin connector at the  
 
end of the Main Cable.  
(2) Audio/Video Input Plugs (RCA) are located at the end of the Main  
Cable. By connecting video and audio signals with these plugs, the  
user can enjoy watching video, only while the parking brake is on.  
Figure 5  
3. Controls and Indicators  
A
B
1
2
H
F
G
C
D
E
Figure 6  
 
Figure 6 illustrates the controls and indicators of the (RVMPKG3) rear  
view mirror:  
A: Rearview mirror  
B: 4” LCD panel  
C: Brightness Controlknob  
D: Power indicator (Red when power is on)  
E: Volume Control Knob  
F: Switch 1 (see below)  
G: Switch 2 (see below)  
H: Speakers  
SW1 and SW2:  
SW1: Used to turn the LCD on/off .  
SW2: Used to toggle display image between rearview camera and  
DVD/VCR.  
Specifications  
General  
Power Supply  
12VDC  
Power Consumption  
Current Draw  
<10W  
<500 mA  
Video Input  
Audio Input  
1Vp-p@ 75 Impedance  
<=500mV  
Audio Power Output  
0.5W × 2 (16O)  
Operating Temperature Range-10? to 60?  
Overall Dimension  
Display System  
Screen  
11W×3.75H×1.25D inch  
4” TFT Color LCD  
250 nit  
Brightness  
 
Contrast ratio  
150:1  
°
°
°
LCD Viewing Angle  
Top-10 , Bottom 30 , Left 45 ,  
°
Right 45  
Resolution  
Video Format  
Display Format  
480×234  
NTSC  
4 : 3  
Maintenance  
Your rearview mirror requires little care, however to maintain it in  
optimum condition follow the procedures below:  
1. Keep your system away from excessive moisture, extreme heat or  
cold and magnetic fields.  
2. Keep liquids away from the display.  
3. Do not place external devices or other objects on the top of the  
mirror.  
Occasionally clean the surface of the mirror with a soft cloth moistened  
with water or window cleaner.  
Troubleshooting  
Table 1 Rearview Mirror  
Symptoms  
Solutions  
The ON/OFF signal light <D> is not  
on after the car is started?  
1. Check the installation-wiring diagram.  
2. Ensure that the parallel red and black line  
is connected properly.  
 
No video signal appears while  
reversing the car?  
1. Check the LCD Contrast (Brightness)  
control knob whether the contrast knob is  
set too low.  
2. Check the rearview Camera lens.  
3. Check the rearview Camera wiring and  
connection.  
4. Check the cable from the rearview mirror  
is connected properly .  
Video image is not sharp enough?  
Clean the lens of the camera.  
 
Figure 7  
 
© 2003 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-6927  
 

3Com Switch 3C16950 User Manual
ADC Network Card H2TU C 319 List 4E User Manual
Altinex Stereo Amplifier DA1912SX User Manual
Alvarion Network Router 214486 User Manual
Amana Refrigerator 3UHSDUH User Manual
Amana Refrigerator W10175445A User Manual
American Aldes Ventilation Hood ERV 200S User Manual
American Standard Indoor Furnishings 0293 Series User Manual
Audiovox Automobile Alarm PRO9801 User Manual
Axis Communications Security Camera P5532 E User Manual