Balcar Computer Monitor BVM D24E1WU User Manual

BID SPECIFICATION  
FOR  
BROADCAST CRT MONITORS  
MODEL NUMBER  
BVM-D24E1WU  
INSTRUCTIONS:  
REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND  
PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST YOU IN  
CLEARLY SPECIFYING THE SONY PRODUCT IDENTIFIED ABOVE, AND ENSURING  
THAT THE BUYER IS WELL INFORMED OF THE HIGH STANDARD OF  
PERFORMANCE THAT IS TO BE EXPECTED OF A SONY PRODUCT. THE  
INFORMATION IN THIS DOCUMENT IS CURRENT AS OF JUNE 2002. PRODUCT  
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.  
SONY ELECTRONICS INC.  
DISPLAY PRODUCTS GROUP  
1 SONY DRIVE, MD 3D9  
PARK RIDGE, NJ 07656  
TEL# (201)-930-1000, FAX# (201)-358-4303  
 
4.0 User Interface / Controllability Information  
Control of this device shall be accomplished through one of the following methods:  
Parallel Remote Control  
RS-485 Serial Control  
This device shall provide a Type II PCMCIA card slot to store monitor settings  
locally.  
The optional parallel remote control shall provide access to all monitor setup  
functions.  
The serial control jack shall employ the use of a standardized device control  
protocol that is understood by external control unit available as an accessory. This  
control jack shall accept bi-directional serial commands that provide full control over  
the device.  
All monitor control functions shall be available for control through the serial control  
jack. This jack shall be capable of connection to an optional serial controller that is  
capable of controlling up to 32 monitors. This optional controller shall be capable of  
storing monitor settings using a Type II PCMCIA flash card.  
Monitor control functions also include auto landing, uniformity adjustments, and auto  
white balance setup using Minolta, Philips, Thoma, and Grasby light probes.  
5.0 Performance Specifications  
This device shall employ the use of an HR Trinitron CRT with a minimum CRT  
resolution of 1000 lines in 16:9 mode and 1000 lines in 4:3 mode. The CRT shall  
employ the use of SMPTE-C phosphors.  
This device shall be equipped with color temperature alignment system for easy set-  
up with industry standard color analyzers. Different colorimetery settings shall be  
able to be recalled for ITU or SMPTE production or film applications.  
This device shall employ built-in auto setup, allowing for automatic adjustment of  
chroma and phase.  
This device shall provide color temperature stability using a beam current feedback  
circuit.  
This device shall employ on-screen display of time code for editing and duplication  
references.  
 
This device shall support switchable aspect ratios of 4:3 and 16:9, and shall offer a  
4:3 area marker.  
This device shall provide beam landing correction to compensate for changes in the  
terrestrial magnetic field in different operating environments.  
This device shall include digital point convergence for complete RGB convergence  
accuracy within the image area. A built-in test pattern generator shall be included for  
assistance in convergence and other monitor setup functions.  
This device shall include a 16:9 tube with the ability to display 4:3 format video.  
6.0 Dimensional Information  
This device shall employ the use of a 24” diagonal (21.88” viewable) CRT.  
This device shall have maximum cabinet dimensions of 17.25 inches high by 22.38  
inches wide and 23.13 inches deep.  
This device shall not weigh more than 113 pounds.  
7.0 Connectivity Information  
This device shall provide for direct connection of a single source device, and shall  
be built with expansion capabilities (4 slots) for additional source devices, with a  
maximum of 25 directly connected sources. This connection shall include the  
following:  
Component Video or RGB Video on BNC Connectors with loop-through  
Optional source connections shall include the following:  
Composite Video on a BNC Connector with loop-through  
S-Video on two BNC Connectors with loop-through  
Component Video or RGB Video on BNC Connectors with loop-through  
SDI Video on a BNC Connector with loop-through  
HD-SDI Video on a BNC Connector with loop-through  
8.0 Power Requirements  
 
This device shall accept power at 100 - 240 VAC at either 50 or 60 Hz.  
This device shall consume no more than 205 watts.  
Power to this device shall be supplied via a detachable standard power cord that is  
readily available for replacement from local suppliers.  
9.0 Safety Compliance Information  
This device shall be fully compliant with the following standards:  
UL 1950  
CSA 950 (cUL listed)  
FCC Class-A  
IC Class-A  
DHHS  
DNHW  
10.0 Warranty Information  
This device shall carry a 2-year manufacturer’s warranty. Authorized servicing  
dealers of the devices’ manufacturer shall perform warranty service.  
 

Acer Computer Monitor S243HL User Manual
ADS Technologies DVD Player USBAV 709 User Manual
AEG Water Heater E User Manual
Aiphone Network Card PS 12F User Manual
Airlink Switch 5 Port User Manual
Aiwa Car Stereo System CDC X145 User Manual
Alpine Speaker SWR 1023D User Manual
American Standard Outdoor Shower 1662602 User Manual
Audiovox Remote Starter AX 901 User Manual
Axis Communications Security Camera M1145L User Manual