Beko Iron BKK 2132 K User Manual

BKK 2132 K  
Household Steam Iron  
User Manual  
 
CONTENTS  
1 Safety Warnings  
2
3
2 Technical Aspects Of Your Machine  
3 Hints For Ironing  
4-8  
9
4 Maintenance And Cleaning  
1
 
1 Safety Warnings  
For safety purpose you should read  
these instructions carefully before  
using the iron for the first time.  
iron or the power cord when ironing.  
2. Do not leave the iron unattended  
when it is connected to a mains  
supply outlet.  
DO’S  
3. Do not use an extension power  
cord set unless competent authority  
has approved it.  
1. Check the mains voltage stated  
on the iron.  
2. Unwind and straighten the power  
cord before use.  
3. Switch on the iron by turning the  
Temperature Dial in clockwise direc-  
tion; pilot light glows.  
4. Turn the Temperature Dial to the  
middle point of 1 dot, 2 dots, 3 dots  
or maximum setting.  
5. Switch off the iron by turning the  
Temperature Dial in anti-clockwise  
direction when it is not in use, even  
for a short period of time. Turn the  
Temperature Dial to°•Min° position.  
6. Disconnect the iron from mains  
supply outlet when filling or emptying  
water.  
4. Do not add perfumed, vinegar or  
other chemical liquids into the water  
tank; they can damage the iron  
seriously.  
5. Do not immerse the iron in water  
or any other liquid.  
6. Do not use the iron when it is  
damaged or it works improperly.  
7. Do not roll the power cord around  
the iron for storage until it has  
cooled down completely.  
8. Do not attempt to open the  
cabinets or dismantle any parts from  
the iron; there is no serviceable part  
inside.  
7. Remove the water remained in the  
water tank.  
8. Use the Self-Cleaning function at  
least once a month.  
9. Switch off the steam function by  
moving the steam control knob to  
position when it is not in use, even  
for a short period of time.  
10. If the supply cord is damaged, it  
must be replaced by the manufac-  
turer or its service agent or similarly  
qualified person in order to avoid a  
hazard.  
DO NOT’S  
1. Do not allow children touch the  
2
 
2 Technical Aspects Of Your Machine  
6
7
4
5
3
8
11  
9
10  
5 4  
2
1
2
1- Spray Nozzle  
7- Auto-shut off indicator  
2- Steam Control/Self-Cleaning Knob 8- Cord storage Button  
3- Water Inlet Cover  
4- Spray Button  
5- Burst Of Steam Button  
6- Pilot Light  
9- Temperature Dial Pointer  
10- Temperature Dial  
11- Filling Beaker  
Voltage/Frequency  
Power  
: 220 - 240 V ~ 50/60 Hz  
: 1850 - 2200 W  
Soleplate  
: PTFE Non stick coated  
Isolation class  
: I  
All declared values on the product and on the printed leaflets are picked up after laboratory  
measurements performed according to related standarts. These values may differ upon usage  
and ambient conditions.  
3
 
3 Hints For Ironing  
1. Sort out the articles to be ironed  
according to the type of fabric.  
This will minimize the frequency of  
temperature adjustment for different  
garments.  
2. Test ironing a small area on the  
backside or inside the garment if you  
are unsure about the type of fabric.  
Start with a low temperature and  
increase gradually.  
3. Wait for about three minutes  
before ironing heat sensitive fabrics.  
Temperature adjustment needs cer-  
tain time to reach the required level  
no matter it is higher or lower.  
4. Delicate fabrics such as silk, wool,  
velour, etc. are best ironed with an  
ironing cloth to prevent shine marks.  
5. You may need a few times of  
press to activate the spray, burst  
and vertically burst function.  
How To Fill Water  
1. Disconnect the iron from mains  
supply outlet.  
2. Move the Steam Control/Self-  
Cleaning Knob to position.  
3. Release the Water Inlet Cover  
4. Fill water through the water inlet  
hole.  
5. Fill up to the ‘Max’ level marked  
on the side of water tank.  
Read The Garment Labels and  
follow the manufacturer’s ironing  
instructions that are often shown by  
symbols similar to the follows:  
Note:  
Do not use chemically descaled  
water or any other liquids.  
Temperature Control Setting  
First Time Ironing  
1. Remove any protective films or  
stickers from the sole plate and the  
cabinet.  
2. Grasp the cord and slowly pull out  
to the length you desired (See How  
to use the Cord storage features)  
3. Fill the water tank. (See How To  
Fill Water)  
. Acetate  
. Elastsne  
. Polyamide  
. Polypropyl-  
ene  
. Cupro  
. Polyester  
. Silk  
. Triacetate  
. Viscose  
. Wool  
. Cotton  
. Linen  
4. Connect the iron to a suitable  
mains supply outlet.  
4
 
5. Turn the Temperature Dial in  
clockwise direction to maximum  
position; pilot light glows.  
dot), ‘••’ (2 dots) or ‘•••’ (3 dots)  
according to the recommendation of  
garment label.  
6. Pilot light goes off when the  
required temperature is reached.  
7. Move the Steam Control/Self-  
Cleaning Knob to position; steam  
starts coming out from the holes in  
the sole plate.  
8. Begin first time ironing with an old  
towel.  
9. When the water tank is empty and  
there is no more steam produced;  
the preparation work is completed.  
The iron is now ready for proper use.  
3. Pilot light glows indicating the iron  
is switched on.  
4. When the required temperature is  
reached; pilot light goes off. The iron  
is ready for use.  
5. Move the Temperature Dial in anti-  
clockwise direction to ‘Min’; the iron  
is switched off.  
6. Disconnect the iron from mains  
supply outlet.  
7. When the iron gets cool complete-  
ly, store it vertically in a safe place  
Steam ironing  
1. Fill the iron as described in How  
Spraying  
To Fill Water.  
2. Connect the iron to a suitable  
mains supply outlet.  
3. Turn the Temperature Dial in  
clockwise direction to ‘•••’ (3 dots)  
setting. (For optimum steam quality,  
do not use 1 dot or 2 dots setting for  
steam ironing)  
4. Pilot light glows indicating the iron  
is switched on.  
1. This function can be used any  
time and is not affect any setting.  
2. Fill the water tank as described in  
How To Fill Water.  
3. Aim the nozzle to the garment.  
4. Press the Spray Button.  
Note: It may be necessary to press  
the spray button a few times to start  
this function.  
5. Pilot light goes off when the  
required temperature is reached.  
6. The iron is ready for use.  
7. Move the Variable Steam Control/  
Self-Cleaning Knob to give the  
desired amount of steam.  
8. Turn the Temperature Dial in anti-  
clockwise direction to ‘Min’; the iron  
is switched off.  
9. Disconnect the iron from mains  
supply outlet.  
10. When the iron gets cool com-  
pletely, store it  
Dry Ironing  
1. Connect the iron to a suitable  
mains supply outlet.  
2. Turn the Temperature Dial in  
clockwise direction; select ‘•’ (1  
5
 
vertically in a safe place.  
ironed and removing the wrinkles.  
8. For stubborn wrinkles, wait a  
few seconds before pressing the  
Burst of Steam Button again. Most  
wrinkles can be removed within three  
presses.  
Note: It may be necessary to press  
the burst of steam button a few  
times to start this function.  
For optimum steam quality, do not  
operate the Burst Of Steam more  
than three times in succession.  
Note: Set the Steam Control Knob  
to position after use.  
Burst of Steam  
Burst of Steam in Vertical Posi-  
tion  
This function provides extra amount  
of steam to remove stubborn  
wrinkles.  
1. Fill the iron as described in the  
section of How To Fill Water.  
2. Turn the Temperature Dial to ‘•••’  
(3 dots) setting.  
Warning: Do not apply steam on  
any clothes or fabrics that are being  
worn by human or pets. Tempera-  
ture of steam is very high.  
This function provides extra amount  
of steam to remove wrinkles on deli-  
cate garments in hanging position,  
hanging curtains, or other hanging  
fabrics.  
3. Pilot light glows indicating the iron  
is switched on.  
4. Pilot light goes off when the  
required temperature is reached.  
5. The iron is ready for use.  
6. Press the Burst Of Steam Button.  
7. Steam will shoot from the holes  
of the soleplate into the fabric being  
1. Fill the iron as described in the  
section of How To Fill Water.  
2. Turn the Temperature Dial to  
‘Max’ setting.  
3. Pilot light glows indicating the iron  
is switch on.  
6
 
4. Pilot light goes off when the  
required temperature is reached. The  
iron is now ready for use.  
5. Hold the iron between 15 and 30  
centimeters away from the garment.  
6. Press the Burst of Steam Button  
once.  
7. Steam will penetrate into the gar-  
ment removing the wrinkles.  
8. For Stubborn wrinkles, wait a few  
seconds before pressing the Burst  
Of Steam Button again.  
9. Most wrinkles can be removed  
within three presses.  
1. Fill the iron as described in How  
To Fill Water; fill the water tank up  
to half.  
Note: It may be necessary to press  
the burst of steam button a few  
times to start this function.  
For optimum steam quality, do not  
operate the Burst Of Steam more  
than three times in succession.  
2. Place the iron on a surface in  
upright standing position.  
3. Connect to a mains supply outlet.  
4. Turn the Temperature Dial in  
clockwise direction to ‘Max’ setting.  
5. Pilot light glows indicating the iron  
is switched on.  
Build-in Anti-scale System  
The build-in anti-scale cartridge is  
designed to reduce the build-up of  
limescale which occurs during steam  
ironing. This will prolonge the work-  
ing life of your iron.  
Note: The anti-scale cartridge will  
not completely stop the natural  
process of limescale build-up.  
6. Pilot light goes off when the re-  
quired temperature is reached.  
7. Wait for one more cycle; pilot light  
glows and goes off.  
8. Turn the Temperature Dial in anti-  
clockwise direction to ‘Min’.  
9. Disconnect the iron from mains  
supply outlet.  
10. Hold the iron horizontally over  
a sink.  
Self-Cleaning  
11. Pull and hold the Steam Control/  
Self-Cleaning Knob to (Descaling)  
position.  
12. Steam and boiling hot water will  
drain from the holes on the soleplate  
washing away the scales and  
minerals that have built up inside the  
Steam Chamber.  
This function removes the scales  
and minerals built up in the Steam  
Chamber. The iron will remain in  
the best condition if this function is  
performed at least once a month  
or more regularly depending on the  
hardness of the water used.  
13. Gently move the iron back and  
7
 
forth until the water tank is empty.  
14. When Self-Cleaning is complete,  
release the Steam Control/Self-  
Cleaning Knob.  
15. Rest your steam iron back on  
its heel rest and allow to fully cool  
down.  
you need to store the iron, grasp  
the plug with one hand and push  
the button on the top cord storage  
device to recoil the cord. Be careful  
not let the snap back towards your  
body  
16. Wipe the soleplate with a cold  
damp cloth.  
Auto Shut-off Features:  
The Auto shut-off feature will oper-  
ate automatically when the iron is  
unattended and it is connected to a  
mains supply outlet.  
Caution: Keep skin/body away from  
the hot water.  
Anti-Drip feature  
Auto shut-off in horizontal  
1. The iron will switch off auto-  
matically at 30 seconds if the iron  
is immobile in the ironing position  
(horizontal).  
2. Auto shut-off indicator light blinks,  
indicating the iron is Auto-Off mode  
3. Simply moving the iron, the iron  
will back on.  
Auto-shut off in vertical  
1. Anti-drip system, which is de-  
signed to prevent water escaping  
from the soleplate when the iron is  
too cold automatically.  
1. The iron will switch off automati-  
cally between 5 to 10 minutes if the  
iron is left on its heel rest position  
(vertically).  
2. During use, the anti drip system  
may emit a loud clicking sound,  
particularly during heat-up or whilst  
cooling down. This is perfectly nor-  
mal and indicates that the system is  
functioning correctly.  
2. Auto shut-off indicator light blinks,  
indicating the iron is Auto-Off mode  
3. Simply moving the iron, the iron  
will back on.  
Note: The iron will take about 60  
seconds to reach its previous sole-  
plate temperature.  
Automatic cord reel Features:  
This iron have equipped with Cord  
storage feature for convenient stor-  
age of the power cord. Grasp the  
cord and slowly pull out the length  
that you need for pressing. When  
8
 
4 Maintenance And Cleaning  
Draining The Water  
to remove the deposits on the sole  
plate.  
Never use any abrasive, vinegar or  
descaling agents to clean the iron.  
1. Move the Steam Control/Self-  
Cleaning Knob to position.  
2. Disconnect the iron from the  
mains supply outlet.  
3. Hold the iron upside down and  
gently shake it to remove any re-  
maining water out of filling hole.  
4. When the iron get cool complete-  
ly, store it vertically in a safe place.  
Note: Set the Steam Control Knob  
to position before storing the iron.  
Cleaning The Iron  
1. Disconnect the iron from the  
mains supply outlet.  
2. Use a damped cloth or non-  
scratching cleaner to remove any  
deposits on the sole plate or the  
cabinets.  
Note:  
Never use sharp or rough objects  
9
 
10  
 

Accton Technology Switch VS4512 User Manual
Acnodes Car Video System PMH 8064 User Manual
Acnodes Computer Monitor APM5084 User Manual
Adcom Stereo Amplifier GFA 7700 User Manual
AdobeAir Humidifier CC2000B User Manual
Air King Air Conditioner 5AU42 9215 User Manual
Air King Air Conditioner AK110PN User Manual
American Audio Speaker PXW 15P15p User Manual
American Standard Outdoor Shower 1662601 User Manual
Barco Computer Monitor MD 4221 User Manual