Eureka Tents Tent 2XTE User Manual

• Raise both poles over the center of the tent  
and secure to the tent fabric with the loop /  
dog bone. Capture both poles at the top. See  
fig.4 and 5.  
Assembly Instructions  
for the Mountain Pass  
2XTE and 3XTE  
fig.4  
fig.9  
Component List:  
1 Tent Body 1 Tent Fly 1 Carry Bag 2 Tent Poles 1 Pole Bag 1 Fly Rod  
14 Stakes & 4 Guy Ropes w/Bag  
1 Gear Loft  
NOTE:  
Do not drop tent bag or pole bag on its end. Do not bounce tent bag on its end to get  
the tent out. These actions may cut the shock cord and/or damage the pole ends.  
Assembly:  
fig.8  
fig.10  
• Unpack the tent bag. Unfold the tent and lay it out, with the floor on the  
ground with a grommeted web in each corner. Pull the tent into a rough  
rectangle. Do not stake down the tent just yet; but in windy conditions,  
stake down one corner that faces into the wind.  
• Assemble the shock corded long tent poles and shorter fly rod. Carefully  
seat each section. Try to keep the poles from snapping together as this  
can damage the ends.  
• At the front of the tent body at A, lay a long tent pole diagonally across  
the tent to the opposite side B. Do the same with the second long pole  
from C to D. See fig.1.  
fig.5  
• Turn the fly right side up and drape it over the tent with  
the fly rod pointing over a door. Align the orange web on  
the fly to the orange web on the tent.  
• Reach under the fly and wrap each Velcro® strap around  
its pole. See fig.10.  
• Attach the clips from the fly to the rings near the floor on  
each side of the tent. See fig.11.  
• Attach the web buckle from each corner of the fly to its  
mate on the tent web. See fig.12. Adjust the corner webs  
to proper tension. Pull out the side webs, stake down and  
adjust. Take care, the fly must not contact the tent wall.  
• Lift the side vents to open and secure the support arm to  
the Velcro® tab. See fig.13.  
• Working your way around the  
fig.11  
tent, attach all the clips from the  
corners of tent to the poles. See  
fig.6 & 7.  
• The tent is now freestanding.  
Place it in the desired location.  
B
D
fig.6  
fig.12  
• Attach a guy-out cord to each corner loop and stake them  
out. See fig.14.  
C
A
• With the poles and tent body  
firmly attached, square the  
tent and pull the wrinkles  
out of the floor. Use a  
metal skewer to stake  
out each corner web.  
See fig.7.  
fig.1  
• Insert the post end of a  
pole into a grommet on  
the corner stake-out web.  
fig.2  
See fig.2.  
fig.13  
• At the opposite corner, grasp the web and simultaneously push the  
pole to form an arc. Insert the post end into the grommet on the  
corner stake-out web. Do this again with the second pole. See fig.3.  
fig.7  
Your Tent  
is Ready!  
• Unroll the fly, upside down, on the ground. Locate the web pockets on  
the fly and insert the assembled fly rod into these pockets. Wrap the  
Velcro® strap around the center of the fly rod. See fig.8 & fig.9.  
Take down:  
• Pull up stakes, remove the fly and open tent doors. Pull posts out of the grommets  
and remove the clips. Collapse the tent poles and stow. Fold the tent and fly. Lay the  
fly and poles on the folded tent. Roll up all towards the door and stow.  
fig.3  
REV C 4.09  
 

Aastra Telecom Answering Machine 6867i User Manual
ACTiSYS Network Card ACT IR220Li User Manual
Adcom Stereo Amplifier GTP 830 User Manual
Advantech Computer Hardware CP 150 User Manual
Allied Telesis Network Card AT A35 SX SC User Manual
AVerMedia Technologies DVR EB3004 MD User Manual
Banner Stereo Amplifier MA3 4 User Manual
Behringer Speaker System B215A User Manual
Beko Refrigerator CN111520 User Manual
Beko Refrigerator CXFD5104 W User Manual